X-Ray and goniometer
SmartLab high-resolution vertical theta/theta goniometer (horizontal sample) equipped with a Cu rotating anode 9 kW    
Fully automated alignment
Independently controlled theta (source) and theta (detector) axes
Measuring range: from  -3 to 160° (2 theta)
Minimal step size : 0.0001°
Scanning speed: 0.01°/min - 20°/min (theta)
Scanning method: coupled theta/theta or independent theta
Motorized Z axe: from – 10 mm  to  +2 mm ; minimum step = 0.0002 mm
In-plane Diffraction Attachment: 2-axis Rx,Ry tilt stage for in-plane alignment
    • Rх tilt rotation: -5.0 – 5.0°, 0.002° step
    • Ry tilt rotation: -5.0 – 5.0°, 0.002° step
    Phi attachment for In-plane Sample Rotation
    • Phi rotation (step or continuous): 360° free rotation, 0.002° step, speed 0.1 – 1000°/min
In-plane arm: 5-axes goniometer (independent 2 theta-chi scan)
From -3° to 120°
Step from 0.002° to 45°
Speed from 0.01 to 40°/min

Incident Optics
Cross Beam Optic (CBO) module with parabolic mirror to select Parallel Beam (PB) or Bragg-Brentano (BB) optical configurations
Variable motorized incident slit from 0.05 mm to 7 mm (step 0.01 mm)
Height limiting slit (also called mask): 0.5, 2, 5, 10 and 15 mm
Soller Slits: 2.5 and 5.0° axial divergence
In-plane Parallel Slit Collimator PSC: 0.5 and 0.15°
Ge (220) 2-bounce incident beam monochromator
 
Sample Stages
High precision motor driven Z-stage for horizontal sample measurement: Z from -10 to 2 mm / 0.0002 mm minimal step coupled with the RxRy tilt stage. Different sample holder can be attached: for powder, for film from few to 10 mm diameter.
High temperature chamber for thin sample analysis: DHS 1100 Anton Paar
    • Operating temperature: room temperature to 1100 °C
    • Atmospheres: vacuum, air, inert gas, nitrogen
   
Diffracted Beam Optics
Modular beam path suitable for a wide range of diffracted beam optical configurations including parallel slit analyzers and dual receiving slits.
    • 2 variable motorized receiving slit Receiving Slits (RS1 and RS2), from 0.05 mm to 20 mm (step 0.01 mm)
Soller Slits:  5.0° axial divergence
Short Parallel Slit Analyzer PSA for in and out-of-plane: 0.5°
    • Long Parallel Slit Analyzer PSA for in and out-of-plane: 0.228° and 0.114° Angular Divergence
Parallel Slit Colimator PSC 0,15°
    • Ni Kbeta filter for Cu radiation
    • Computer-Controlled Rotating Attenuator: Auto ; 1/70 ; 1/1000 ; 1/4000 ; Open
Beam-stop

Detector
NaI scintillation counter and measuring electronics provide 700,000 cps, with automated dead time correction.
High resolution 2D RIGAKU HyPix 3000 Detector. Large active area of approximately 3000 mm² with a small pixel size of 100 μm², resulting in a detector with high spatial resolution. High count rate of greater than 10⁶ cps/pixel, a fast readout speed and essentially no noise. Ultra-high dynamic range and high sensitivity. Seamless switching from 2D-TDI (Time Delay and Integration) mode to 2D snapshot mode to 1D-TDI mode to 0D mode with a single detector. XRF suppression by high and low energy discrimination.
    • Computer-controlled detector with the RIGAKU Guidance software
    • 0D - 1D - 2D modes: can be used in any case (alignment, BB, PB, ..) directly from Guidance
    • active zone: 77.5 x 37.5mm
    • Pixel: 100 x 100mm